Resin · Guide

How to Prevent Bubbles in Resin

Why bubbles show up in epoxy and UV resin, and the mixing, temperature, and sealing habits that keep them out.

Bubbles are trapped air, trapped moisture, or a resin so cold and thick that air cannot leave. They are rarely a mystery of the brand. Most of them are stirred in, poured in, or cooked out of a wet flower after the lid is already on the mold.

Start with the temperature

Cold epoxy is viscous. Viscous resin holds the bubbles your stir stick just created. Work in a comfortable room, roughly the low-to-mid 70s °F, and warm sealed bottles in a bath of warm water until they are not cold to the touch. Do not microwave the bottles. Do not open them in the water. Dry the outside before you pour. A drop of bath water in the cup clouds the cure and can leave it sticky.

Do not try to “save” a cold pour by blasting it with a heat gun for a full minute. That cooks the surface, can yellow it, and does nothing for bubbles already locked in a thick layer.

Mix like you are trying not to make foam

Stir slowly for the full time on the label. Scrape the sides and the bottom. Then pour the mix into a second cup and stir again. Makers call that a double cup. It catches the unmixed streak that causes soft spots, and it gives a few bubbles a chance to rise before they are in the mold.

Do not whip. A drill mixer is an efficient way to laminate air into a coaster. If the resin is still ribboned with unmixed streaks at the end of the stated time, keep stirring slowly. Speed is not thoroughness.

Let the mixed cup sit for a couple of minutes if the working time allows it. Tap the cup. Bubbles that can leave will come to the surface. Pour down a stir stick in a thin stream, close to the mold, instead of dumping from a height that folds air back in.

Seal anything that can off-gas

Wood, paper, cardboard, dried flowers, and open-cell fabric all hold air and water. Under resin they let it go, and the bubbles appear half an hour later, after you have stopped watching.

Give wood a thin seal coat of the same resin and let it gel before the flood coat. Dry flowers and leaves need to be actually dry: days or weeks in a press or silica, not “picked this morning and patted with a towel.” Moisture in a petal becomes a bubble and often a brown spot. Inkjet ink can smear. Seal paper and test a scrap. A laser print is usually calmer than a fresh inkjet sheet, and neither is guaranteed.

If you are embedding a photograph in a coaster, the coaster guide puts the seal step in order.

After the pour

Wait a minute. Pop what reaches the surface. A toothpick is the right tool for one bubble in a bezel. A heat gun on low, in quick passes, several inches away, pops a field of surface bubbles. Do not hover. Lingering heat yellows resin and can boil a thin pour.

A butane torch is faster and less forgiving. It is easy to scorch a mold, a paper inclusion, or the resin itself. It is also a bad partner for isopropyl alcohol mist. If you use alcohol at all, keep flame and a hot gun away from the vapor.

Some makers mist 91% isopropyl on an epoxy surface to pop bubbles. It works often enough that people swear by it, and it also causes haze and fisheyes when it is heavy. A lot of manufacturers do not recommend it. Prefer a short pass of heat and a cleaner mix. If you experiment, do it on the test pour, not on the piece you planned to give away.

Cover the work with a bin propped on spacers, or a box that is not clamped airtight. The goal is dust, not a sealed chamber. Dust that lands in the gel stage becomes a permanent speck. You cannot brush it off later without sanding.

Depth, layers, and humidity

A pour deeper than the label allows will hold bubbles and may overheat. Either choose a casting resin rated for that depth or pour in layers. A second layer usually wants the first layer still tacky, inside the pour window the maker describes. If you missed that window and the first layer is fully cured, scuff it lightly, wipe the dust, and then pour. A glossy cured surface can refuse the next layer.

Very humid rooms make some epoxies blush, which is a waxy film, or fill with microbubbles. A dry day is easier. In a wet climate a dehumidifier in the work room does more than a new jar of glitter.

UV resin is a different bubble

UV layers are thin, so a toothpick and a quick cure solve most of them. Do not count on a heat gun. Heat can yellow UV resin or start to set it before the bubble has left. Keep the layer thin enough that you can see the bottom. If you cannot see it, the lamp cannot reach it either. The UV jewelry guide covers the tacky surface that people mistake for bubbles.

What a pressure pot actually does

A pressure pot shrinks bubbles while a casting cures, by pressurizing the chamber. It does not suck air out. A vacuum chamber degasses resin before the pour, and it can foam the cup over. They are different machines. Neither belongs on a first shopping list.

If you buy a pressure pot later, buy one built and rated for the job, with a safety valve, and use a compressor the pot’s rating allows. Do not improvise a pressurized vessel. This is not a project for a modified paint tank and a guess.

Tools, if the mix is already careful

Tool

Graduated mixing cups

Two marked cups per pour: one to measure and mix, one to transfer into. The transfer is the bubble and the soft-spot control.

Price: check Amazon. It changes with size, seller, and coupons. Castwick does not store a live price, star rating, or review count.

Amazon search: graduated resin mixing cups

View current listings on Amazon (opens in a new tab)

Affiliate link. A qualifying purchase may earn Castwick a commission.

Tool

Craft heat gun

A small heat gun, used in short passes, is the usual surface-bubble tool after the pour. It is not a mixer and not a way to force a cold, thick resin to behave.

Price: check Amazon. It changes with size, seller, and coupons. Castwick does not store a live price, star rating, or review count.

Amazon search: heat gun for resin crafts

View current listings on Amazon (opens in a new tab)

Affiliate link. A qualifying purchase may earn Castwick a commission.

The habit order is temperature, slow mix, second cup, sealed inclusions, then a brief pass of heat. People who buy the heat gun first and whip the resin anyway will still have bubbles. They will just have warmer bubbles.