Resin · Guide
A Resin Coaster Project and Kit Guide
A first resin coaster project: kit or separate supplies, the pour order, and the mistakes that leave a soft spot.
A set of four coasters is the right first epoxy project. The piece is shallow, the mold does the edges, and you can see a mixing mistake before you have flooded a table. This is the order of work, plus how to tell a real kit from a mold, a bag of glitter, and a bottle with no ratio.
Kit or separate supplies
A kit is reasonable when it names the resin, prints the mix ratio and the cure time, and includes enough resin for the molds in the box. If any of those are missing, buy a simple silicone mold and a coating epoxy you can read. The buying guide is the label checklist. Anonymous “resin coaster kit” listings are cheap because the instructions were the first thing cut.
You need a level work surface, nitrile gloves, graduated cups, stir sticks, a timer, a dust cover, and the mold. Mica is optional and should wait until a clear test coaster has cured hard. Felt or clear silicone bumpers are for the end, so the coaster does not stick to a finished table.
How much resin
A 4-inch square at 1/8 inch thick is 2 cubic inches, about one fluid ounce of mixed resin, before the waste that stays in the cup. Four coasters are on the order of 4 fluid ounces plus that waste. Your mold may be deeper. The better measurement is a water test: fill one dry mold with water, pour the water into a measuring cup, and note the volume. Dry the mold completely. Water left behind will cloud the epoxy. Mix that volume per coaster, plus a little for the cup.
Do not fill past the rim unless you plan to sand a dome off. Overflow is how edges stay soft and how resin glues the mold to your board.
The pour, in order
Protect the table and level the board. Resin is a liquid level. If the board tilts, one edge is thick and the other is starved. Tape a floppy mold down so it cannot creep.
Gloves on before the bottles open.
If you are embedding paper or a photo, seal it and let the sealer dry. A glue stick, a dry decoupage layer, or packing tape can work. Test the ink. Inkjet smears. Give the scrap a day, not ten minutes, if the sealer says it needs that. Unsealed paper turns blotchy or releases bubbles halfway through the cure. Flowers have to be fully dry. The bubble guide is the reason this step is not optional.
Measure the two parts. Stir for the full labeled time, scraping the wall and the bottom. Pour into a second cup and stir again. This is where soft spots are prevented. A soft corner is almost always unmixed resin, not “the mold.”
Pour down a stir stick. Wait a minute. Pop surface bubbles with a toothpick or a short pass of a heat gun from several inches away. Do not stir the mold. Do not hover with the gun until the resin ripples and yellows.
Mica, if you use it, gets stirred into a small cup of already mixed resin and then poured. That is control. Alcohol ink dropped into the mold is a stunt: one drop moves a long way and can fisheye. Learn mica first.
Cover the molds with a bin on spacers. Do not poke the piece while it is gelling. Fingerprints at the gel stage are permanent.
Demold when the label says you can, not when you are curious. If the label says 24 hours to demold and 72 hours to a full cure, do not stack the coasters at lunchtime and do not put them in service that night. A soft demold warps. Warped coasters also come from an unlevel board.
Edges, feet, and dust
If a sharp lip remains, wet-sand it under a trickle of water, 220 grit and then 400. Wear a dust mask if you dry-sand. Cured resin dust is an irritant and does not belong in a kitchen cloud. Wipe the slurry off. Clear silicone bumpers keep the coaster from stamping a finish on a table. Felt dots work until they get wet and grimy. Bumpers are the less fussy choice.
Failures, named plainly
A tacky face or a soft corner is a ratio or mixing problem. Scrape better and measure again. Do not pour the rest of the kit on top and hope.
A white bloom or cloud over paper is moisture or unsealed ink. Seal a scrap next time.
Bubbles that appear late are an inclusion off-gassing, not a stir you can still fix. Let this piece finish. Change the prep.
Fingerprints mean you touched it too soon. The cure time was the instruction.
A coaster that rocks was demolded soft or poured on a tilt. Check the level before you blame the mold.
Supplies to compare
Kit
Beginner resin coaster kit
Only consider a kit that names the resin, the mix ratio, and the cure time, and that includes enough resin for its own molds. If the bottle in the photos has no label text, buy the mold and the epoxy separately.
Price: check Amazon. It changes with size, seller, and coupons. Castwick does not store a live price, star rating, or review count.
Amazon search: resin coaster kit with epoxy and silicone molds
View current listings on Amazon (opens in a new tab)Affiliate link. A qualifying purchase may earn Castwick a commission.
Epoxy
1:1 coating epoxy
A shallow coaster is a coating-resin job. ArtResin is one widely sold 1:1 example. Match the pour depth on the label to the mold you measured with the water test.
Price: check Amazon. It changes with size, seller, and coupons. Castwick does not store a live price, star rating, or review count.
Amazon search: ArtResin epoxy resin 1 to 1 kit
View current listings on Amazon (opens in a new tab)Affiliate link. A qualifying purchase may earn Castwick a commission.
Mold
4-inch silicone coaster mold
Square or round, about 4 inches, is a standard first set. A mold with a very deep well may exceed a coating resin. Measure it.
Price: check Amazon. It changes with size, seller, and coupons. Castwick does not store a live price, star rating, or review count.
Amazon search: silicone coaster mold 4 inch for resin
View current listings on Amazon (opens in a new tab)Affiliate link. A qualifying purchase may earn Castwick a commission.
Color
Resin mica pigment
A small set is enough. Stir mica into mixed resin in a separate cup. You do not need a 40-jar collection to see whether you like the look.
Price: check Amazon. It changes with size, seller, and coupons. Castwick does not store a live price, star rating, or review count.
Amazon search: mica powder for epoxy resin
View current listings on Amazon (opens in a new tab)Affiliate link. A qualifying purchase may earn Castwick a commission.
Finish
Clear silicone bumpers
Stick-on bumpers keep cured coasters from sitting in a puddle of contact with a finished table. Add them after the full cure, on a clean, dry back.
Price: check Amazon. It changes with size, seller, and coupons. Castwick does not store a live price, star rating, or review count.
Amazon search: clear silicone bumper pads for coasters
View current listings on Amazon (opens in a new tab)Affiliate link. A qualifying purchase may earn Castwick a commission.
Make one clear coaster before you make a set with inclusions. The clear one tells you whether the ratio and the cure are real. The decorated ones can wait a day. That wait is the whole difference between a project and a pile of soft plastic.